Mastheadgraphiconline

introduced 2004

• Exceptionally fast auto-focus
• 4 fps continuous shooting
• Rugged metal body with ergonomic design and quartz-date back
• Distance-linked E-TTL II flash metering
• 7 wide-area focusing points, selected automatically, with eye-control or manually
• 35-zone metering linked to focusing points
• 13 custom functions with 34 settings to personalise your camera
•11 shooting modes including six PIC modes
• Ultra-quiet operation and film transport system
• Full range of EF lenses and EOS accessories available

A replacement for the EOS 33. Similar to the EOS 30V, but without eye-control focus.

EOS magazine, March 2003, page 62

Type and Major Components
Type
35mm autofocus and autoexposure single-lens reflex camera with focal-plane (vertical travel) shutter, built-in motor drive and built-in flash.
Picture size: 24mm x 36mm
Compatible lenses: Canon EF lenses
Lens mount: Canon EF mount (metal)

Autofocusing
Type: TTL-CT-SIR (Through-the-Lens Cross-Type Secondary Image Registration) with CMOS sensor.
Focusing points: 7 (extreme left, left, top, center, bottom, right, extreme right).
Focusing modes:
• One-shot AF: AF operation stops (AF lock) when focus is achieved. Set automatically in the portrait, landscape, close-up and nightn scene modes.
• Predictive AF with AI Servo AF: Tracks subject movement continuously up to the start of exposure. Set automatically in sports mode.
•AI focus AF: Automatically switches between One-Shot AF and Predictive AF / AI Servo AF if sufficient sunject movement is detected. Set automatically in the full auto mode.
• Manual focusing: After the lens focus mode switch iss set to M or MF, manual focusing is enabled with the focusing ring. In-focus indicator in viewfinder lights wehn focus is found. When metering is active, MF icon in viewfinder flashes when manual focus is selected.
Focusing point selection:
• Eye control: Creative zone shooting modes only.
(i) One-Shot AF: the eye selects the focusing point by looking at it in the viewfinder while the shutter button is pressed halfway.
(ii) AL Servo AF: AF operation starts in the same way as with the One-Shot AF, but while the shutter button is pressed halfway during continuous shooting the moving subject is tracked by the focusing points the eye looks at.
(iii) AI Focus AF: the AF operation starts in the same way as with the One-Shot AF. However, if the subject starts moving after focus is achieved in the One-Shot AF mode, the camera switches automatically to AI Servo AF.
•Automatic focusing point selection: Set automatically in the Full Auto and Programmed Image Control modes; can be set manually in Creative zone modes. Automatic focusing point selection is set when you try to select a focusing point beyond the outermost ones during manual focusing point selection.
(i) One-Shot AF: based on the subject information obtained by the seven focusing points, the camera focuses the nearest subject automatically. With the Eye Control switch turned ON in Full Auto or Program Image Control modes, the eye position is detected automatically and this information is incorporated in the automatic focusing point selection algorithm. This increases the chances for the camera to select the focusing point that the user wants.
(ii) AI Servo AF: AF usually starts with the centre focusing point. If the subject moves to another focusing point, AI Servo AI will continue to track the subject. If AF starts with the subject focused by an off-centre focusing point, the subject will still be tracked even if it moves to an adjacent focusing point.
(iii) AI Focus AF: the One-Shot AF mode focuses the optimum subject based on the subject information obtained by the seven focusing points. If the centre focusing point focuses the subject first and the subject starts to move, the AF mode switches to AI Servo AF and the subject is tracked even if it moves to another focusing point. Only the centre focusing point can detect initial subject movement; if an off-centre focusing point focuses the subject first, subject movement will not be detected.
• Manual focusing point selection: Enabled in the Creative Zone modes; not available in the Full Auto and Program Image Control modes. AF is executed with the manually selected focusing point. With Custom Function 11-0, pressing the focusing point selector button enables the focusing point selection keys. However, setting Custom Function 11-1 provides the following:
(i) Eye Control: after focus is achieved, the focusing point selection keys are enabled.
(ii) Automatic focusing point selection: while the shutter button is pressed halfway and the metering active, manual focusing point selection is enabled. During automatic focusing point selection, pressing focusing point selection keys starts the selection with the centre focusing point.
(iii) Manual focusing point selection: enabled while the shutter button is pressed halfway and the metering active. The focusing point selection keys can be used without having to press the focusing point selector first. During manual focusing point selection, pressing the focusing point selector switches to automatic focusing point selection.
Manual focusing point selection is disabled in Full Auto and Programmed Image Control modes, so this Custom Function setting does not apply in these modes.
During manual focusing point selection, if the selection goes beyond the outer-most focusing point, automatic focusing point selection is set.
Eye Control Calibration: calibration is enabled when the Eye Control switch is set to CAL. Up to five sets of calibration settings can be saved.
Focusing point display: the selected focusing point is indicated by superimposition (SI) in the viewfinder and the icon is shown on the LCD panel. During automatic focusing point selection, multiple focusing points might be displayed. Custom function 10-1 disables the SI display. The SI brightness cannot be changed.
AF activation: by pressing the shutter button halfway.
AF operation speed: same as the EOS-3.
In-focus indicator: icon in viewfinder (LCD), superimposed (SI) focusing point display, and beeper. The in-focus beeper can be enabled or disabled in all the picture-taking modes. In the AI Servo AF mode, the in-focus indicator and beeper are disabled.
AF precision: same as the EOS 650.
AF working range: EV 1-18 (at ISO 100)
AF-assist: intermittent burst fired by built-in flash (no patterned beam). Fired automatically when necessary and linked to all seven focusing points. Effective range approx. 4 meters at centre. Coverage: 28mm lenses. Fired automatically in low light (EV 4 or lower at ISO 100). Automatic pop-up and AF-assist light in the Full Auto, Portrait, Close-up, and Night modes. Disabled in Landscape and Sports modes. Manual pop-up and firing in P, Tv, Av, M, and DEP modes. AF-assist can be enabled/disabled with CUstom Function 7. AF-assist light turns off when the in-focus signal is detected.
With EX/EZ/E-series Speedlites AF-assist beam is emitted by the external unit. Speedlite 420EX: compatible with all focusing points. Speedlites 550EX/540EZ: the AF-assist patterned beam is not compatible with top and bottom focusing points. With other EOS-dedicated speedlites AF-assist beam is not emitted when an off-centre focusing point has been selected.

Viewfinder
Type: Eye-level, single-lens reflex type with fixed pentaprism and condenser lens.
Focusing screen: Fixed New Laser-matte screen with 7 focusing points.
Standard dioptre: -1 dioptre
Dioptric adjustment range: -2.5 to +0.5 dioptres.
Eye relief: 19.5mm
Viewfinder coverage: 90% vertical, 92% horizontal.
Magnification: 0.70x (with 50mm lens at infinity)
Viewfinder information:
On the screen: focusing points with superimposed display.
Below the screen (icon; numeric and text information with 7-segment yellow/green LCD):
• shutter speed (if out-of-range, blinks at 2Hz as a warning)
• aperture (if out-of-range, blinks at 2Hz as a warning)
• FEL display (displayed for about 0.5 second during FE lock)
• DEP display (DEP-1, DEP-2)
• CAL display (CAL-1 to CAL-5; blinks if Eye Control fails)
• END display (END-1 to END-5
• AE lock, FE lock
• exposure compensation amount*
• flash exposure compensation amount*
• manual exposure level*
• AEB range*
• red-eye reduction lamp-on indicator (progressive)
• flash-ready indicator
• insufficient flash warning during FE lock
• high-speed sync (FP flash)
• eye control icon (blinks at 2Hz when eye control fails)
• flash exposure compensation icon
• AF in-focus indicator (blinks at 2Hz when AF fails)
• MF in-focus indicator
* 2 stops in 1/2-step increments
Viewfinder information cannot be disabled.
Quick-return half mirror: transmission reflection ratio of 40:60
Viewfinder blackout time: 155ms or shorter with shutter speed of 1/60 second or faster.
Mirror lockup: enabled with Custom Function 5-1. Only one frame is shot even in the continuous shooting mode. Maximum mirror lockup operation time of 30 seconds.
Mirror vignetting: no vignetting with an EF 600mm f/4L IS USM or shorter lens (except for EF 50mm f/1.0L USM.
Depth-of-field preview: depth-of-field preview button provided; enabled in creative zone modes only (disabled in Full Auto and Programmed Image Control modes). With Speedlite 550EX or MR-14EX attached pressing the depth-of-field preview button fires the modelling flash.
Bulit-in eyepiece shutter: none (eyepice cover provided on the neck strap)
Mirror noise: lower than 70dB.
Other specifications: eye cup Ed provided. Angle Finder C, Angle Finder B, and Magnifier S attatchable (adapter required). Ed-series dioptric adjustment lenses are physically attachable, but not recommended. Built-in dioptric adjustment should be used instead.

Exposure control
Type: TTL maximum aperture metering with a 35-zone silicon photocell. The follwoing three metering modes are provided (selectable in creative zone modes with metering mode botton on the back):
• evaluative (automatically set in Full Auto and PIC modes)
• partial metering at centre; approx. 10% of viewfinder. Custom Function 8-1 enables partial metering to be linked to the active focusing point.
• center-weighted averaging metering.
AE modes:
• intelligent program AE (shiftable)
• shutter speed priority AE (no safety shift)
• aperture-priority AE (no safety shift)
• depth-of-field AE (DEP/Shiftable)
• full auto (intelligent program AE / not shiftable)
• programmed image control modes: Portrait, Landscape, Close-up, Sports, Night scene
• metered manual
• E-TTL program flash AE
• A-TTL program flash AE
• TTL program flash AE
Metering range: EV 1-20 (at 20"C with 50mm f/1.4 lens, ISO 100)
Insuficient exposure warning: LCD digital display blinks at 2Hz on LCD panel and in the viewfinder.
Exposure metering: activated when shutter button is pressed halfway. Metering continues to be active for 4 seconds after the shutter button is released.
Film speed range: ISO 25 to 5000 with DX-coded film, set automatically in 1/3-stop increments. The ISO film speed is displayed on the LCD panel during the initial film advance to the first frame. ISO 6 to 6400 in 1/3-stop increments manually. With non-DX-coded film, the ISO film speed of the film previously loaded is displayed during initial film advance to the first frame; the ISO on the LCD panel then blinks, stopping when the film speed is set manually.
Exposure compensation:
• AEB (Autoexposure Bracketing): is enabled with the function setting and settable in the creative zone modes. The bracketing range is 2 stops in 1/2-stop increments. The bracketing sequence is correct exposure, underexposure and overexposure. Compatible in single-frame and continuous film advance modes. With the self-timer, all three bracketed shots will be taken after 10 second self-timer delay. Cancellation enabled by setting the AEB range to 0. AEB is not cancelled if the lens is changed. AEB is not available in the Full Auto and Programmed Image Control modes.
• Manual exposure compensation: is enabled in the creative xone modes. Compensation amount 2 stops in 1/2-stop increments.
If AEB and exposure compnesation are combinded, the AEB range will be shifted in accordance with the exposure compensation amount.
• Flash exposure compensation: is possible with built-in flash and EOS-dedicated external Speedlite and enabled with the function setting. The compensation amount is stops in 1/2-stop increments. If flash exposure compensation is set on both the camera and the external Speedlite, the Speedlite's setting will override the camera setting. Flash exposure compensation is not available in the Full Auto and Program Image Control modes.
• AE lock: automatic AE lock is enabld with One-shot AF and evaluative metering, AE lock is applied when focus is achieved. An AE lock button enables AE lock in creative zone modes. AE lock is applied during partial metering at the centre focusing point (Custom Function 8-1 enables partial metering to be linked to active focusing point). With an EX-series Speedlite, the AE lock button becomes an FE lock button. Custom Function 4-1 enebles AE lock with the shutter button.
Multiple exposures: a maximum of 9 multipe exposures can be set )enabled with Function setting). Cancelled automatically after all multiple exposures are taken. The number of multiple exposures can be altered (increased, decreased, or cancelled) during multiple-exposure shooting. Not avaiable in Full Auto and Programmed Image Control modes.

Shutter
Type: Vertical-travel, focal-plane shutter with all speeds electronically-controlled. First and second curtains both have dedicated electromagnetic release control. Curtain speed: 4.8ms/24mm.
Shutter speeds: 30 seconds to 1/4000 second in 1/2-stop increments. X-sync at 1/125 second. No elapsed-time indicator during bulb exposures. If the shutter button is fully depressed while the camera back is open. the shutter speed is always 1/4000 second (this protects the shutter curtains).
Shutter release: soft-touch electromagnetic release. No cable release socket.
Self-timer: electronically-controlled, 10 second delay. Set with the film advance mode lever. Enabled in all picture-taking modes. Can be cancelled before shutter button is pressed by turning the command dial to 'Off' or by turing the film advance mode lever to another setting. Can be cancelled after the shutter button has been depressed by turning the command dial, popping up or retracting the built-in-flash, or changing the lens. Reflex mirror swings up at the start of the 10-second period.
Self-timer indicator: red-eye reduction lamp blinks at 2Hz for the first 8 seconds then lights for the remainging 2 seconds. Frame counter on the LCD panel counts down from 10 to 1 seconds. Beeper sounds at 2Hz for first 8 seconds and then at 8Hz for the remaining 2 seconds (beeper sounds only when enabled with the Custom Function setting).
Camera shake warning: provided in Full Auto and Programmed Image Control modes. If the shutter speed is slower than 0.5 stop below the reciprocal of the lens focal length, the shutter speed display blinks at 2Hz.

Film transport
Film loading: automatic take-up with a sprocketless system. After the film leader is positioned correctly the camera back is closed, the film advances to frame 1 automatically (as displayed on the frame counter), taking about 1 second.
Film advance system: automatic film advance using a small coreless motor: Film perforation detected with an infrared photo reflector (not compatible with infrared film).
Film advance modes:
• single-frame shooting
• continuous shooting
• self-timer/remote conrol
Film advance modes set automatically in Full Auto and Program Image Control modes. Set manually with film advance lever in creative zone modes.
Film advance initiation: Exposure-completed signal automatically starts film advance.
Continuous shooting speed: maximum speed of approx. 4 fps (One-shot AF mode, shutter speed 1/250 second or faster, new batteries, 20 degrees C). Maximum speed in AI Servo AF mode of approx. 3.5 fps.
Film advance indicator: the frame counter counts up.
Film rewind system: automatic rewind with a small coreless motor.
Film rewind initiation: Automatic rewind: rewind initiated automatically under the following conditions:
• after 24 or 36 exposures (read from DX-coded film)
• detection of end of film or roll (increased tension)
• after 36 exposures are taken (overrides other conditions)
Midroll film rewind: midroll rewind button starts film rewind. During film rewind, pressing the midroll rewind button switches the rewind between silient and high-speed rewind. Custom Function 1-1 sets high-speed rewind.
Film rewind indicator: the frame counter counts down. The exposure level scale under the viewfinder screen also indicates film rewind is in progress; the scale bars 'flow' from right to left (also displayed on the LCD panel).
Film rewind: stops automatically after the film leader is rewound completely inside the cartridge (Custom Function 2-0) or automatically with the film leader left outside the cartridge (Custom Function 2-1). Film cartridge icon on LCD pannel blinks at 2Hz to indicate film rewind completion.
Film-loaded indicator:
• LCD panel: indicated by the film cartridge icon.
• Film window: visual confirmation.
Frame counter: electronic counter with digital display. Counts up during film advance and down during film rewind.

Built-in-flash
Type: built-in, auto pop-up TTL autoflash head in the pentraprism. Manually retractable. Series-circuit controlled.
Guide number: 13 (ISO 100, meters).
Recycling time: approx. 2 seconds.
Flash-ready indicator: flash icon lights in viewfinder. Flash icon turns off when the flash is not reead, and the shutter cannot be released.
Flash coverage: covers 28mm lenses.
Flash switch: none. Automatic pop-up in low light and back lit conditions in Full Auto and Programmed Image Control modes (except Landscape and Sports modes). Manual pop-up (pull up by hand) in creative zone modes. Retracts manually (push down by hand) in all modes.
Synchronisation speed: maximum X-sync speed at 1/125 second.
• Full Auto, Program AE, DEP, Portrait, Close-up modes: automatically set between 1/60 and 1/125 second.
• Night Scene mode: automatically set between 2 seconds and 1/125 second (in 1/2-stop increments).
• shutter speed-priority AE and manual modes: set manually at 1/125 second or slower.
• Aperture-priority AE mode: set automatically between 30 seconds and 1/125 second to suit the ambient light.
In the night scene and sports modes, the built-in flash cannot fire, but an external Speedlite can be used.
Flash exposure system: TTL off-the-film autoflash exposure with focusing point-linked 3-zone flash metering. Flash metering is weighted on the selected focusing point.
Evaluative metering weighting: if the center, top or bottom focusing point is selected, the sensitivity of adjacent zones is reduced by one stop. If the right or extreme right focusing point is selected, the sensitivity of adjacent zones is reduced by one stop. If the left or extreme left focusing point is selected, the sensitivity of adjacent zones is reduced by one stop.
Flash output control: automatic flash output reduction for back lit conditions or fill-in flash.
Flash exposure compensation: up to 2 stops in 1/2-stop increments. Flash exposure compensation can be set with the camera for built-in flash or external Speedlite.
Effective range: with EF 28-105mm f3.5/4.5 II USM lens
• ISO 100/28mm: 1 to 5.2 meters (1 to 3.7 metres)
• ISO 100/105mm: 1 to 4 metres (1 to 2.8 metres)
• ISO 200/28mm: 1 to 7.4 metres (1 to 5.2 metres)
• ISO 200/105mm: 1 to 5.7 metres (1 to 4 metres)
• ISO 400/28mm: 1 to 10.5 metres (1 to 7.4 metres)
• ISO 400/105mm: 1 to 8.1 metres (1 to 5.7 metres)
Distances are for negative film (distances for slide film in brackets) At shooting distances shorter than 1 meter the flash coverage will be partially obstructed by the lens barrel.
Sufficient/insufficient flash indication: none.
Curtain synchronization: first curtain synchronization. Second-curtain synchronization with built-in flash enabled with Custom Function 6-1.
Flash duration: 1 ms or shorter.
Colour temperature: equivalent to daylight.
Distance to optical axis: 73mm between the flash head centre and lens optical axis.
Power source: batteries in the camera.
Red-eye reduction: with the built-in flash popped up, the red-eye reduction lamp lights and then the flash fires.
• type: lamp.
• commpatible modes: all picture-taking modes except Landscape and Sports.
• setting method: function setting.
• lamp ON preconditions: lights after shutter button is pressed halfway and focus achieved with One-shot AF or MF. (in AI Servo AF mode, shutter release-priority takes effect even while the lamp is lit.)
• duration: under the conditions stated in above, the lamp lights while the shutter button is pressed halfway and dims after 1.5 seconds (with the self-timer it lights for 2 seconds before shutter release.)
• lamp ON indicator: the exposure level scale (bars) on the LCD panel and in the viewfinder indicates lamp-on for 1.5 seconds.
• shutter release lock: none (shutter-release has priority).
The above red-eye reduction operating conditions also apply when an external Speedlite is used.

Date imprinting (QD model only)
Type: auto date using 7-segment LCD in the imprinting element.
Data range: 1.1.1994 to 12..31.2019. Automatic adjustment for leap years.
Imprinted modes:
• month, day, year
• day, month, year
• year, month, day
• day, hour, minute
• blank
Pressing the MODE button changes the imprinting mode in a looping sequence.
Imprinting position: lower right of picture.
Imprinting colour: orange.
Imprinting conformation: none.
Imprinting brightness: automatically set to suit DX-coded film speed.
QD power source: one CR2025 lithium battery (3volt) housed on the inside of the QD back. The date is reset when the battery is replaced.

Power source
Batteries: two CR123A lithium batteries (6 volt) loaded through the camera grip buttom.
Battery check: automatic battery check when the command dial is released from OFF. Battery level is always indicated on the LCD panel in one of four levels:
• battery OK
• keep spare batteries handy
• replacement warning (shutter release not locked)
• replacement warning (shutter release locked)
Main switch: command dial set to OFF turns camera off.

Other camera specifications
Custom functions: thirteen custom functions (C.Fn-1 to C.Fn- 13, 34 settings) provided. Settable with the command dial turned to C.Fn.
• C.Fn-1: film rewind speed (0: silent; 1:high speed)
• C.Fn-2: film leader position after rewind (0:inside cassette;2: outside cassette).
• C.Fn-3: DX-coded film speed setting (0: enabled; 1: disabled).
• C.Fn-4: shutter button ( o ) and AE lock button ( • ) functions (0:( o ) AF and AE star, ( • ) AE lock; 1: ( o ) AE lock, ( • ) AF and AE start; 2: ( o ) AF and AE start, ( • ) AF stop.
• C.Fn-5: mirror lockup (0: disabled; 1: enabled).
• C.Fn-6: shutter curtain flash synchronisation (0: first curtain synchronisation; 1: second curtain synchronisation).
• C.Fn-7: AF-assist light/flash firing (0: AF-assist/flash fires; 1: no AF-assist/flash fires; 2: AF-assist from Sppedlite/flash fires; 3: AF-assist/no flash fires).
• C.Fn-8: partial metering/FE lock linkage with focusing point (0: centre focusing point; 1: active focusing point).
• C.Fn-9: Flash sync speed in aperture priority mode (0: selected to suit ambient light; 1:set to 1/125 second).
• C.Fn-10: in-focus focusing point on focusing screen (0: superimposed; 1: not shown).
• C.Fn-11: focusing point selection method (0: focusing point selector and keys; 1: focusing point selector keys; 2: focusing point selector and main dial).
• C.Fn-12: start with centre focusing point (0: disabled; 1: enabled).
• C.Fn-13: lens AF stop button (some IS lenses only) (0: stops AF; 1: starts AF; 2: AE lock during metering; 3: switched from manual to automatic focusing point selection; 4: switches between One-shot AF and AI Servo AF; 5: start image stabilizer).
Camera back: opened with camera back latch. Film window provided. No film memo holder. Not detachable.
Camera orientation detection switch: provided.
Flash contacts: X-sync direct contact on hot shoe. Speedlite locking pin hole provided. No PC terminal.
External display: large LCD panel on camera top.
Shutter button lock: electronic lock when command dial set to OFF.
Remote control terminal: for remote switch RS-60E3 (2.5mm diameter minijack remote control terminal).
Interchangeable grip: none.
Body material: aluminium and polycarbonate resin with glass fibre.
Exterior colour: black.
Dimensions:
• QD model: 146.7 (W) x 103 (H) x 69 (D)mm
• non-QD model: 146.7 (W) x 103 (H) x 69 (D)mm

Speedlite operation in program AE mode
EX-series Speedlites: E-TTL autoflash; normal flash
When the flash is ready, the synchronization speed (1/60 to 1/125 second) is set automatically. The aperture is set automatically by the camera's E-TTL program. When the shutter button is fully depressed, a fixed-output preflash is fired just before the mirror swings up. The AE sensor meters the ambient light before the preflash and the light reflected off the subject from the preflash. The output of the main flash is thereby determined before the main flash fires. The main flash then fires.
If the EX-series Speedlite's high-speed synchronization (FP flash) switch is on and the brightness is still too high for the smallest aperture, the high-speed synchronization mode is set automatically. When high-speed synchronization is set, the appropriate icon lights in the viewfinder.
Automatic fill-in flash is possible.
EX-series Speedlites: E-TTL autoflash; FE Lock
When an EX-series Speedlite is attatched and the flash is ready, the AE lock button becomes an FE lock button. Pressing the AE lock button fires a preflash. The AE sensor, with partial metering, reads the preflash light reflected off the subject. The flash output is thereby determined and retained in memory. When the shutter button is fully depressed, the flash fires at the output retained in memory.
If the EX-series Speedlite's high-speed sync (FP flash) switch is on and the brightness is still too high for the smallest aperture, hgih-speed synchronization mode is set automatically. When high-speed synchronization is set, the appropriate icon lights in the viewfinder.
When the FE lock button is pressed and the flash is ready, a preflash is fired and FE lock takes effect. If the flash will be insufficient (underexposure of more than 0.5 stop compared to the correct flash exposure), the flash ready icon blinks as a warning before the picture is taken.
Automatic fill-in flash is possible.
Built-in flash: TTL autoflash
When the flash is ready. the synchronization speed (1/60 to 1/125 second) is set automatically. The aperture is set automatically by the camera's TTL program. TTL off-the-film autoflash control with 3-zone flash metering linked to focusing point. Automatic fill-in flash is possible.
EZ/E-series Speedlite: A-TTL autoflash
When the flash is ready, the synchronization speed (1/606 to 1/125 second) is set automatically. The optimum aperture is set automatically by the camera's A-TTL program and the result of the Sppedlite's near-infrared preflash to suit the subject's distance and brightness. TTL off-the-film autoflash control with 3-zone flash metering linked to the focusing point. Automatic fill-in flash is possible.
ML-3 and 480EG: TTL autoflash metering
Same as built-in flash: TL autoflash (above).
With all the above, a shutter speed of 1/125 second or slower can be selected when the camera is set to shutter speed priority AE. Also, when an EX-series Speedlite is attatched and the high-speed synchronisation (FP flash) switch is on, a synchronisation speed faster than 1/125 second can be set. In the aperture-priority AE mode, any aperture can be selected.
M/T/A-series Speedlites
Manual or external flash metering required.
• picture-taking mode: manual.
• synchronization speed: set manually from 30 second 1/125 second or bulb.
• flash aperture: set the same aperture value manually on the camera and Speedlite.
Non-Canon flash unit
• compact flash units: set the shutter speed to 1/125 second or slower.
• studio flash: set the shutter speed to 1/60 second or slower (test required).
Wireless flash
Enabled with 550EX or MR-14EX (master unit). Three-group (A,B,C) slave control, high-speed synchronization, FE lock, flash ratio (A:B) control, FEB, flash exposure compensation and modelling flash (with flash ratio) enabled.
Flash exposure compensation: settable with camera or EOS-detected Speedlite. 2 stops in 1/2-stop increments (if set in both the camera and Speedlite, the Speedlite's flash exposure compensation setting takes priority).
FEB: settable with Speedlite (550EX, MR-14EX). Not settable with camera. Any flash exposure compensation set with the camera is not combined with FEB.
Modelling flash: fires (at 70 Hz for 1 second) with depth-of-field preview button when 550EX or MR-14EX is used.

Wireless remote control
Configuration: consists of a built-in sensor in the camera grip and Remote Controller RC-1 (sold separately).
Channels / modes (RC-1): 1 channel; 2 modes and lock
• immediate shutter release (mirror lockup is not possible).
• 2 second delay.
Setting method: film advance lever set to Self-timer/Remote control.
Transmission: enabled with RC-1's transmission button (emits intermittent infrared light with a peak wavelenthg of 950nm).
Reception: via the camera grip's built-in SPC.
Effective range: approx. 5 metres (with front and centre transmission angle) or 3.5 metres (with transmission angle of 25 degrees from film plane).
Operation indicator:
• immediate shutter release signal reception: the red-eye reduction lamp blinks once as the picture is taken.
• 2-second delay signal reception: the red-eye reduction lamp lights for 2 seconds. A countdown of '2, 1' is displayed on the LCD panel. The beeper sounds at 8Hz (when enabled by the function setting).
Cancellation: no operation by user for 4 minutes cancels the Self-timet/Remote control setting automatically. Setting restored when the user touches the camera controls.
Bulb exposure: for bulb exposures, the remote control signal reception can start the exposure immediately or after a 2 second delay. When the signal is received again, the bulb exposure stoops.

Canon is making a habit of launching new EOS cameras in pairs ? one digital and one film. Last September saw the introduction of the EOS 300D and the EOS 3000V. Now we have the EOS 1D Mark II and the EOS 30V Date. (The EOS 33V is the EOS 30V Date without eye-control focus and without the Quartz Darte back.)

The EOS 30V Date is an upgrade of the EOS 30, a mid-range camera aimed at enthusiasts. A key feature for many users is the eye-control focus. After you have calibrated this to your eye-sight, the camera focuses the lens to match the area of the image you look at. As you look at different areas of the viewfinder screen, the focus follows your eye. This feature is mostly unchanged on the new EOS 30V Date.

Many of the changes are, in fact, fairly minor. Canon has taken the opportunity to enhance the appearance of the camera and add some features requested by users of the earlier model.

Exterior appearance
The EOS 30V Date camera body features an aluminium exterior with a black leather-tone finish. Some of the dials and buttons have been redesigned to make them easier to read. The LCD now has backlight illumination for use in low light. One of the main changes is the addition of a quartz-date back as standard. This enables you to imprint the date or time of shooting on your frames at the moment of exposure.

Improved flash
The EOS 30V Date (along with the new EOS 1D Mark II) uses an improved E-TTL flash system. On previous models, the E-TTL flash metering was based on the amount of a pre-flash reflected back to the camera from the subject. While this works well in most situations, exposure may not be correct if the subject is very light in tone, or there are highly reflective surfaces in the subject area.

The new cameras introduce subject distance into the flash algorithms. E-TTL flash metering is now able to identify and ignore areas of the subject which are showing unusually high levels of reflected light. The system is also able to prevent overexposure when there is no subject at a manually-selected focus point. The new E-TTL flash metering system is only effective with dedicated Speedlite flashguns.

Faster focusing
The speed at which the camera focuses has been boosted and is now similar to the focusing speed of the EOS 1V. The predictive focusing capability also matches that of the EOS 1V and EOS 3. A new 'random-type' focusing screen provides a good balance between focusing accuracy and brightness.

unfortunately we don't have a press release section for this product yet. However , our website is being constantly updated so please check back soon.

key features
specifications
information

EOS 33V

EOS 33V

accessories

lenses

manuals

press release
reartab
item4
item20a
item14a

SUBSCRIBE HERE

item13a
item11a
item10a

Sign up to our free newsletter

EQUIPMENT:

Lenses

Speedlites

Digital cameras

Film cameras

item2a

HOME

MAGAZINE

EQUIPMENT

SHOP

LINKS

CLASSIFIEDS

FORUM

GALLERY

NEWS